Pillowcase Romper Tutorial

Hello everyone! I found this cute green polka dot material at the thrift store a while back and it just really wanted to be made into something and what could be easier than a pillowcase dress?? Well, pillowcase dresses I've done before, and I just wanted something new, something a little different. So, I morphed it into the pillowcase romper!

I will preface this by saying I learned a lot in the process of making this romper. I had several firsts as I created this, but none were truly as terrifying as I had built them up to be. One of those being the snaps... I had never used my snap pliers despite having them for probably over a year. Piece of cake. If I can do it, you can do it. :)  I have made a few adjustments to this tutorial since making this romper Little J is wearing and I will point these things out as we go.

Materials:

• 3/4 to 1 yard of fabric
• 1/2 in. elastic
• 1/4 in. elastic
• 1/2 in. double fold bias tape
• snaps

There are a few measurements you will need to get of your child.

1. All the way around your child's chest.
2. From right between your child's shoulders to ankles.
3. Between your child's shoulders to the inseam (crotch.)
4. Armpit to armpit across the front.
5. Around your child's lower leg (lower calf/shin area.)

Take the number you got for #1 and double that to get the width of your fabric you need to cut.  Take the number you got for #2 and add 2 inches for the length.  My fabric piece is 24 x 38.

Now fold that piece in half lengthwise right side to right side.  Sew down the side with a 1/2 in. seam allowance.

Finish that seam and then iron.  Turn right side out.  Now to make the arm holes, measure 3-4 in. across and 3-4 in. down and mark with a fabric marker or chalk.  (For an 18 month size do 3" x 3".  My arm holes turned out a little too big.)

Now you are going to cut out the shape of a J on both of those corners using the marks you just made.

Turn inside out again and fold the top front piece down 1/4 in. and iron.  Then fold down another 1 in. and iron.  Repeat for the top back piece also.  This will be your elastic casing.

Now sew across the bottom edge of your casing stitching closely to the fold.

Now lay your romper out flat and fold in half.  Take the number you got for #3 and add 1.5 in. to that.  Using that number measure down from the top of the elastic casing.  Mark at the side edge of your romper.

Cut out a piece shaped like my cut in the picture below.

When you open it back up it will look like this.

Now you need to get out some of your extra left over fabric.  Take the piece you just cut from your romper and lay it on top of the extra fabric.  Trace the scrap.  Then you need to make another line 1.5 inches around that.

Cut this shape out.  You will do it twice.  It will look like this.

Turn your romper right side out again.  Lay the U-shaped piece on top of it right sides facing and pin like in the picture below.  You will do this for the front and back side of the romper.

Now you will sew with a 1/4 in. seam allowance around the inside of the legs of your romper one side at a time.

Fold in the outer edge of your U-shaped fabric piece and iron.  It will wrinkle slightly in the curve and that is fine.

 Now take that whole piece and fold it under your romper and iron down.

 Now stitch down along the outer edge of the U-shaped piece. 

Fold up the bottom of each leg 1/4 in. and press, then another 1/4 in. and press.  Hem.

This is what you should have so far.

Now take measurement from #4 above and cut 2 pieces of your 1/2 in. elastic.  Using a safety pin you will feed one piece of elastic into the front of your romper and pin in place, and then repeat for the back side with your other piece of elastic.

Next you want to mark where you will place your snaps.  I spaced mine about 2.5 in. apart around the leg openings.  You want to make it so that the back piece of fabric comes over the front piece to snap.  Look at one of your child's onesies to see what I mean.  Make sure that you have the snaps facing the proper directions before you squeeze them on because they are darn near impossible to get off if you put them on wrong.

Using the measurement from #5 above cut two pieces of 1/4 in. elastic.  Take one of them and place right above the hem on one leg of your romper.  Sew it down 2-3 stitches and backstitch.  Now pull taut and stitch all the way across the leg opening.  Repeat for the opposite leg.

It will create this gathered effect like in the picture below.

Hang in there we are almost finished now I promise!  Take out your bias tape and cut it in half creating two strips for your side ties.  Fold one strip in half to find the center of the tape.  Open up the tape and fold over the side seam in our arm hole so that your ties will be centered.  Repeat for the opposite arm hole using your other strip of bias tape.

Starting at the very end of one of your bias tape strips sew across the short end.  Turn and sew all the way down the side stitching around the arm hole and across the opposite end of the strip.  Repeat for the opposite side.

Ta-Da!  Now put it on your child and take lots of pictures!!

This romper would also look super cute layered with a t-shirt for the fall!  Hope you love it!

Pattern Testing

This feels like it has been one nonproductive week.  Every project I have started has ended up taking longer than I anticipated, because one thing went wrong or another.  Please tell me I am not the only one who has weeks like this?  I was starting to think I had lost my crafty touch.  Starting this week full of projects has got to be better.  I started it off today with a bang by completing a pattern testing for Petite Kids Boutique on the cutest little sundress that she is calling the Haven sundress.  I'm betting you will see it in her shop in the next week or so.  It really was an easy pattern to follow and the results should just speak for themself.  ADORABLE!

Rainbow Ripple Baby Blanket - Pattern Review

After a very long and painful wait trying to adopt, my cousin finally got word she was going to get a baby girl.  I had already had my eye on a few patterns for a baby blanket for her when the time came, so I pulled up all my bookmarked patterns and looked through the yarn I had trying to decide which was right for her.  I am a member of www.ravelry.com and I got the Rainbow Ripple Baby Blanket pattern by Celeste Young from Ravelry as a free download.  If you crochet or knit and you are not a member of that site, go join now.  :) 

I found the pattern to be very easy to follow.  It was well written and all the stitch counts came out correctly.  I changed up the color combinations and the number of rows per color to fit my own color palette, and that was not difficult to do either.  I used cotton yarn which made it very soft.  I got a lot of compliments on this afghan and my cousin has used the afghan in several of this sweet baby's portraits since her birth 5 months ago.

Don't you just want to squeeze her!!